motive_calibrating
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
motive_calibrating [2019/08/21 07:01] – 178.197.228.241 | motive_calibrating [2019/08/21 08:26] – [Calibration with Active Wand] 10.130.132.100 | ||
---|---|---|---|
Line 33: | Line 33: | ||
**Place a marker** inside the tracking space as a reference. | **Place a marker** inside the tracking space as a reference. | ||
- | {{ :: | + | {{ :: |
| | ||
Line 58: | Line 58: | ||
===== Calibration with Passive Wand ===== | ===== Calibration with Passive Wand ===== | ||
+ | |||
+ | Make sure that the **Tracking Mode is set to Passive**. Otherwise, press '' | ||
+ | |||
+ | {{:: | ||
+ | |||
=== Masking === | === Masking === | ||
Line 63: | Line 68: | ||
Once all the reflections are removed, Clear the previously set masks by pressing '' | Once all the reflections are removed, Clear the previously set masks by pressing '' | ||
- | {{ :: | + | {{ :: |
=== Wanding == | === Wanding == | ||
Line 71: | Line 76: | ||
Take the '' | Take the '' | ||
- | The cameras will indicate with a blue LED light, when they detecting the markers of the wand (also indicating the direction by the position of the blue light in the circle). The LED light will turn into green when the wanding was successful. | + | The cameras will indicate with a blue LED light, when they detecting the markers of the wand (also indicating the direction by the position of the blue light in the circle). The LED light will turn into green when the wanding was successful. Do not wand to close to the cameras, **keep at least 3m distance from the cameras**. |
Keep on **wanding util each cameras LED circle is fully green** and you have reached **at least 5000 samples** on each camera. | Keep on **wanding util each cameras LED circle is fully green** and you have reached **at least 5000 samples** on each camera. | ||
+ | {{:: | ||
+ | {{:: | ||
+ | {{:: | ||
+ | {{:: | ||
+ | {{:: | ||
+ | |||
+ | |||
+ | After wanding, press '' | ||
+ | |||
+ | {{:: | ||
=== Ground Plane === | === Ground Plane === | ||
+ | {{:: | ||
+ | {{ :: | ||
+ | Place the L shaped ground plane in the **middle of the room**, facing the long side to the large door. | ||
+ | Press '' | ||
+ | If you get an error message, that no Ground Plane can be found, try to find the 3 Markers in the 3D view, select them and press '' | ||
+ | |||
+ | If setting Ground Plane is successful, you will be promted to **save the calibration**. Choose your session folder and create a subfolder **Calibration**. | ||
+ | |||
+ | |||
+ | The calibration is now finished. | ||
===== Calibration with Active Wand ===== | ===== Calibration with Active Wand ===== | ||
+ | Make sure that the **Tracking Mode is set to Active**. Otherwise, press '' | ||
- | {{ ::motive-30.png?300|}} | + | {{::motive-4.png?200| Active Tracking Mode}} |
- | then set the masks again (press "Mask visible" | ||
- | {{: | + | === Masking === |
- | once the masks are set, the space is ready for wanding. make sure you are using the correct wand (500mm) | + | Once all the reflections |
- | {{: | ||
- | keep on wanding until each camera has at least 1500 Samples: | + | {{ :: |
- | {{: | + | === Wanding == |
- | press calcualate: | + | Select '' |
- | {{:calculate.png?400|}} | + | Take the '' |
+ | |||
+ | The cameras will indicate with a blue LED light, when they detecting the markers of the wand (also indicating the direction by the position of the blue light in the circle). The LED light will turn into green when the wanding was successful. Do not wand to close to the cameras, **keep at least 3m distance from the cameras**. | ||
+ | |||
+ | Keep on **wanding util each cameras LED circle is fully green** and you have reached **at least 5000 samples** on each camera. | ||
+ | |||
+ | {{:: | ||
+ | {{:: | ||
+ | {{:: | ||
+ | |||
+ | {{:: | ||
+ | {{:: | ||
+ | |||
+ | |||
+ | After wanding, press '' | ||
+ | |||
+ | {{:: | ||
+ | |||
+ | |||
+ | === Ground Plane === | ||
- | once the result looks like this: | + | Make sure that the **Tracking Mode is set to back to Passive**. Otherwise, press '' |
- | {{:solution.png?400|}} | + | {{::motive-3.png?200| Passive Tracking Mode}} |
- | confirm | + | If you plan to use the tracking system with projections, |
- | {{:applysolutiondialog.png?400|}} | + | {{:: |
+ | {{ ::motive-29.png?300 Set Ground Plane|}} | ||
- | and as the last step set the ground plane. The ground plane L has a defect waterbalance, so please do not adjust | + | Place the L shaped |
- | {{: | + | Press '' |
- | Vertical Offset is the distance from the ground | + | If you get an error message, that no Ground Plane can be found, try to find the 3 Markers in the 3D view, select them and press '' |
- | the ground plane Z-Axis should point towards the computers. there are three markers on the trackingspace that indicate the position. | + | If setting Ground Plane is successful, |
- | {{: | ||
- | save the callibration file inside [[motive_sessions|your session folder]]. | + | The calibration is now finished. |
{{: | {{: |
motive_calibrating.txt · Last modified: 2019/08/21 21:24 by nkottman