motive_calibrating
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
motive_calibrating [2019/08/21 07:50] – 10.130.132.100 | motive_calibrating [2019/08/21 21:24] (current) – nkottman | ||
---|---|---|---|
Line 58: | Line 58: | ||
===== Calibration with Passive Wand ===== | ===== Calibration with Passive Wand ===== | ||
+ | |||
+ | Make sure that the **Tracking Mode is set to Passive**. Otherwise, press '' | ||
+ | |||
+ | {{:: | ||
+ | {{ :: | ||
+ | |||
=== Masking === | === Masking === | ||
Line 63: | Line 69: | ||
Once all the reflections are removed, Clear the previously set masks by pressing '' | Once all the reflections are removed, Clear the previously set masks by pressing '' | ||
- | {{ :: | ||
=== Wanding == | === Wanding == | ||
Select '' | Select '' | ||
+ | |||
+ | {{ :: | ||
Take the '' | Take the '' | ||
Line 83: | Line 90: | ||
- | After wanding, press '' | + | After wanding, press '' |
{{:: | {{:: | ||
- | |||
=== Ground Plane === | === Ground Plane === | ||
+ | If you plan to use the tracking system with projections, | ||
+ | {{:: | ||
+ | {{ :: | ||
+ | Place the L shaped ground plane in the **middle of the room**, facing the long side to the large door. | ||
+ | |||
+ | Press '' | ||
+ | |||
+ | If you get an error message, that no Ground Plane can be found, try to find the 3 Markers in the 3D view, select them and press '' | ||
+ | |||
+ | If setting Ground Plane is successful, you will be promted to **save the calibration**. Choose [[motive_sessions|your session folder]] and create a subfolder **Calibration**. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The calibration is now finished. | ||
===== Calibration with Active Wand ===== | ===== Calibration with Active Wand ===== | ||
+ | Make sure that the **Tracking Mode is set to Active**. Otherwise, press '' | ||
+ | {{:: | ||
+ | {{ :: | ||
+ | === Masking / LED === | ||
- | and as the last step set the ground plane. The ground plane L has a defect waterbalance, | + | Clear the previously |
- | {{: | ||
- | Vertical Offset is the distance from the ground to the center of the reflectors. | + | === Wanding == |
- | the ground plane Z-Axis should point towards the computers. there are three markers on the trackingspace that indicate the position. If you plan to use the tracking system with projections, | + | Select '' |
- | {{:groundplate.jpg?400|}} | + | {{ ::img_0709.jpg?200|Active wand}} |
- | save the callibration file inside | + | Take the '' |
+ | |||
+ | The cameras will indicate with a blue LED light, when they detecting the markers of the wand (also indicating the direction by the position of the blue light in the circle). The LED light will turn into green when the wanding was successful. Do not wand to close to the cameras, **keep at least 3m distance from the cameras**. | ||
+ | |||
+ | Keep on **wanding util each cameras LED circle is fully green** and you have reached **at least 5000 samples** on each camera. | ||
+ | |||
+ | {{:: | ||
+ | {{:: | ||
+ | {{:: | ||
+ | |||
+ | {{:: | ||
+ | {{:: | ||
+ | |||
+ | |||
+ | After wanding, turn of the wand and press '' | ||
+ | |||
+ | {{:: | ||
+ | |||
+ | |||
+ | === Ground Plane === | ||
+ | |||
+ | **Enable the LED lights** of the cameras by pressing '' | ||
+ | |||
+ | Make sure that the **Tracking Mode is set to back to Passive**. Otherwise, press '' | ||
+ | |||
+ | {{:: | ||
+ | |||
+ | If you plan to use the tracking system with projections, | ||
+ | |||
+ | {{:: | ||
+ | {{ :: | ||
+ | |||
+ | Place the L shaped ground plane in the **middle of the room**, facing the long side to the large door. | ||
+ | |||
+ | Press '' | ||
+ | |||
+ | If you get an error message, that no Ground Plane can be found, try to find the 3 Markers in the 3D view, select them and press '' | ||
+ | |||
+ | If setting Ground Plane is successful, you will be promted to **save the calibration**. Choose | ||
{{: | {{: | ||
+ | |||
+ | The calibration is now finished. |
motive_calibrating.1566366622.txt.gz · Last modified: 2019/08/21 07:50 by 10.130.132.100